内牛……bigadv算到一半……重启之后从0开始了……

金鹏 · 发表于 2011-9-21 16:39:04

回复 24# shouldbe

感觉是兄弟的虚拟机网络没设置好，要是懒得折腾跑跑WIN下的BIGADV也不错，PPD也有30K+

bugfix · 发表于 2011-9-22 13:11:49

这种情况也遇到过，所以从这个礼拜开始工作用机开始跑smp2了。

shouldbe · 发表于 2011-9-22 13:27:38

3.9G主频下PPD20000出头。虽然不是很高，不过还是很欣慰了。一个礼拜算一个bigadv我也心满意足了。

Shadowmourne · 发表于 2011-9-22 14:57:23

本帖最后由 Shadowmourne 于 2011-9-23 12:33 编辑

回复 33# shouldbe

不应该吧……
我Q154@2.6GHz如果放着不用……PPD都20K+……(7164分的那几个bigadv)

shouldbe · 发表于 2011-9-23 11:11:52

回复 34# Shadowmourne

今晚23:47。结束。希望明天晚上回家的时候俺的第一个bigadv已经上传。

ONLY · 发表于 2011-9-23 11:26:30

3.9G主频下PPD20000出头。虽然不是很高，不过还是很欣慰了。一个礼拜算一个bigadv我也心满意足了。 ...
shouldbe 发表于 2011-9-22 13:27

原生Linu环境BIGADV折腾心得，供兄弟参考：

如果需要折腾硬件（超频、调整BIOS、换硬件等等神马滴），那么就先用浏览器打开管理页面，Stop Folding先～～～

等提示客户端停止，再用网上邻居把work目录、queue.dat、untinfo.txt文件拷贝到某台机器备份～～～

一切妥当后再去shutdown或reboot～～～

以前偶都是直接reboot，木有备份，结果最近杯具的爆掉了两个包，其中一个已经算到80%，又从0开始～～～
确保硬件系统足够稳定～～～

话说偶的BIGADV专机上面使用的硬盘和电源都是早先跑分很久的东东（大于一年），所以换到BIGADV机器上面基本不用担心这些部件的稳定性～～～
养成备份的好习惯～～～

偶现在工作机上一般开一个FastCopy，隔上几个小时就把BIGADV机器上面的任务包拷贝到本地机器暂存，时时预防运算出错～～～
网络的话，注意检查网线接头，不行就重做水晶头～～～

偶用过一条成品线，原来一直很好，最近搬家，貌似出了点问题～～～

非要用劲塞进网线口，才会有反应～～～

这样的情况，果断重做个水晶头啦～～～

BIGADV包算完后上传便要一小时左右（ADSL），中途任何网络不稳定都有可能造成杯具～～～

偶一般都是使用某台机器大流量下载，然后用手拉扯各个网线头，并ping路由，看看延时情况～～～

这样大约能发现一些隐性的网络问题～～～

供参考～～～

Shadowmourne · 发表于 2011-9-23 12:31:48

回复 35# shouldbe

[17:36:07]
[17:36:07] *------------------------------*
[17:36:07] Folding@Home Gromacs SMP Core
[17:36:07] Version 2.27 (Thu Feb 10 09:46:40 PST 2011)
[17:36:07]
[17:36:07] Preparing to commence simulation
[17:36:07] - Looking at optimizations...
[17:36:07] - Created dyn
[17:36:07] - Files status OK
[17:36:09] - Expanded 24871129 -> 30796292 (decompressed 123.8 percent)
[17:36:09] Called DecompressByteArray: compressed_data_size=24871129 data_size=30796292, decompressed_data_size=30796292 diff=0
[17:36:09] - Digital signature verified
[17:36:09]
[17:36:09] Project: 6900 (Run 10, Clone 23, Gen 55)
[17:36:09]
[17:36:09] Assembly optimizations on if available.
[17:36:09] Entering M.D.
[17:36:15] Mapping NT from 8 to 8
[17:36:18] Completed 0 out of 250000 steps  (0%)
[18:15:31] Completed 2500 out of 250000 steps  (1%)
[18:52:52] Completed 5000 out of 250000 steps  (2%)
[19:30:06] Completed 7500 out of 250000 steps  (3%)
[20:07:15] Completed 10000 out of 250000 steps  (4%)
[20:44:23] Completed 12500 out of 250000 steps  (5%)
[21:21:35] Completed 15000 out of 250000 steps  (6%)
[21:58:42] Completed 17500 out of 250000 steps  (7%)
[22:35:45] Completed 20000 out of 250000 steps  (8%)
[23:13:00] Completed 22500 out of 250000 steps  (9%)
[23:21:28] - Autosending finished units... [September 22 23:21:28 UTC]
[23:21:28] Trying to send all finished work units
[23:21:28] + No unsent completed units remaining.
[23:21:28] - Autosend completed
[23:50:16] Completed 25000 out of 250000 steps  (10%)
[00:27:37] Completed 27500 out of 250000 steps  (11%)
[01:04:47] Completed 30000 out of 250000 steps  (12%)
[01:41:54] Completed 32500 out of 250000 steps  (13%)
[02:19:02] Completed 35000 out of 250000 steps  (14%)
[02:56:03] Completed 37500 out of 250000 steps  (15%)
[03:38:56] Completed 40000 out of 250000 steps  (16%)
[04:20:35] Completed 42500 out of 250000 steps  (17%)

这是现在正在算的一个包……抽出昨天晚上睡觉时候算的部分……
1%-11%吧……比较好算
6h12m=10%
于是每1%是37min12s左右
http://www.linuxforge.net/bonuscalc2.php
这里算出的结果是总分56097、PPD21715……
CPU是2720QM ES Q154
用turbostat可以看到现在的频率是2.64GHz……

运行环境是fedora 15 64bit……
windows和linux运算效率差这么大吗……

shouldbe · 发表于 2011-9-23 13:00:29

我用虚拟机linux在4.5G下不到30分钟1%。linux就是这么强。

谢谢only的指点。不过很可惜大部分内容我做不到。原因很简单，实在没有精力去折腾电脑了。折腾的多了，老婆意见很大。所以现在采取最简单的措施：winxp bigadv客户端随机启动，主频下调到3.9G，温度控制在60度以下，周一到周五基本不在家，可以开算（满打满算有希望算完两个），周六回家只算SMP。对我来说这是最好的方案了。

shouldbe · 发表于 2011-9-24 12:25:03

悲剧，算完了，但不能上传

[14:28:25] Completed 245000 out of 250000 steps  (98%)
[15:04:19] Completed 247500 out of 250000 steps  (99%)
[15:40:13] Completed 250000 out of 250000 steps  (100%)
[15:40:28] DynamicWrapper: Finished Work Unit: sleep=10000
[15:40:38]
[15:40:38] Finished Work Unit:
[15:40:38] - Reading up to 52713120 from "work/wudata_09.trr": Read 52713120
[15:40:38] trr file hash check passed.
[15:40:38] - Reading up to 47067560 from "work/wudata_09.xtc": Read 47067560
[15:40:39] xtc file hash check passed.
[15:40:39] edr file hash check passed.
[15:40:39] logfile size: 236831
[15:40:39] Leaving Run
[15:40:43] - Writing 100185451 bytes of core data to disk...
[15:40:44] ... Done.
[15:40:53] - Shutting down core
[15:40:53]
[15:40:53] Folding@home Core Shutdown: FINISHED_UNIT
[15:40:56] CoreStatus = 64 (100)
[15:40:56] Unit 9 finished with 57 percent of time to deadline remaining.
[15:40:56] Updated performance fraction: 0.611579
[15:40:56] Sending work to server
[15:40:56] Project: 6900 (Run 54, Clone 17, Gen 4)

[15:40:56] + Attempting to send results [September 23 15:40:56 UTC]
[15:40:56] - Reading file work/wuresults_09.dat from core
[15:40:56] (Read 100185451 bytes from disk)
[15:40:56] Connecting to http://130.237.232.141:8080/
[15:44:54] - Couldn't send HTTP request to server
[15:44:54] + Could not connect to Work Server (results)
[15:44:54]    (130.237.232.141:8080)
[15:44:54] + Retrying using alternative port
[15:44:54] Connecting to http://130.237.232.141:80/
[16:26:45] - Autosending finished units... [September 23 16:26:45 UTC]
[16:26:45] Trying to send all finished work units
[16:26:45] - Already sending work
[16:26:45] + Sent 0 of 1 completed units to the server
[16:26:45] - Autosend completed
[16:43:04] - Couldn't send HTTP request to server
[16:43:04] + Could not connect to Work Server (results)
[16:43:04]    (130.237.232.141:80)
[16:43:04] - Error: Could not transmit unit 09 (completed September 23) to work server.
[16:43:04] - 1 failed uploads of this unit.
[16:43:04] Keeping unit 09 in queue.
[16:43:04] Trying to send all finished work units
[16:43:04] Project: 6900 (Run 54, Clone 17, Gen 4)

[16:43:04] + Attempting to send results [September 23 16:43:04 UTC]
[16:43:04] - Reading file work/wuresults_09.dat from core
[16:43:04] (Read 100185451 bytes from disk)
[16:43:04] Connecting to http://130.237.232.141:8080/
[17:43:45] - Couldn't send HTTP request to server
[17:43:45] + Could not connect to Work Server (results)
[17:43:45]    (130.237.232.141:8080)
[17:43:45] + Retrying using alternative port
[17:43:45] Connecting to http://130.237.232.141:80/
[18:13:36] - Couldn't send HTTP request to server
[18:13:36] + Could not connect to Work Server (results)
[18:13:36]    (130.237.232.141:80)
[18:13:36] - Error: Could not transmit unit 09 (completed September 23) to work server.
[18:13:36] - 2 failed uploads of this unit.

[18:13:36] + Attempting to send results [September 23 18:13:36 UTC]
[18:13:36] - Reading file work/wuresults_09.dat from core
[18:13:36] (Read 100185451 bytes from disk)
[18:13:36] Connecting to http://130.237.165.141:8080/
[18:13:37] - Couldn't send HTTP request to server
[18:13:37] + Could not connect to Work Server (results)
[18:13:37]    (130.237.165.141:8080)
[18:13:37] + Retrying using alternative port
[18:13:37] Connecting to http://130.237.165.141:80/
[18:13:37] - Couldn't send HTTP request to server
[18:13:37] + Could not connect to Work Server (results)
[18:13:37]    (130.237.165.141:80)
[18:13:37] Could not transmit unit 09 to Collection server; keeping in queue.
[18:13:37] + Sent 0 of 1 completed units to the server
[18:13:37] - Preparing to get new work unit...
[18:13:37] Cleaning up work directory
[18:13:37] + Attempting to get work packet
[18:13:37] Passkey found
[18:13:37] - Will indicate memory of 3575 MB
[18:13:37] - Detect CPU. Vendor: GenuineIntel, Family: 6, Model: 10, Stepping: 7
[18:13:37] - Connecting to assignment server
[18:13:37] Connecting to http://assign.stanford.edu:8080/
[18:13:39] Posted data.
[18:13:39] Initial: ED82; - Successful: assigned to (130.237.232.141).
[18:13:39] + News From Folding@Home: Welcome to Folding@Home
[18:13:39] Loaded queue successfully.
[18:13:39] Sent data
[18:13:39] Connecting to http://130.237.232.141:8080/
[18:13:45] Posted data.
[18:13:45] Initial: 0000; - Receiving payload (expected size: 24865701)
[18:17:12] - Downloaded at ~117 kB/s
[18:17:12] - Averaged speed for that direction ~118 kB/s
[18:17:12] + Received work.
[18:17:12] Trying to send all finished work units
[18:17:12] Project: 6900 (Run 54, Clone 17, Gen 4)

[18:17:12] + Attempting to send results [September 23 18:17:12 UTC]
[18:17:12] - Reading file work/wuresults_09.dat from core
[18:17:12] (Read 100185451 bytes from disk)
[18:17:12] Connecting to http://130.237.232.141:8080/
[18:17:13] - Couldn't send HTTP request to server
[18:17:13] + Could not connect to Work Server (results)
[18:17:13]    (130.237.232.141:8080)
[18:17:13] + Retrying using alternative port
[18:17:13] Connecting to http://130.237.232.141:80/
[18:17:13] - Couldn't send HTTP request to server
[18:17:13] + Could not connect to Work Server (results)
[18:17:13]    (130.237.232.141:80)
[18:17:13] - Error: Could not transmit unit 09 (completed September 23) to work server.
[18:17:13] - 3 failed uploads of this unit.

[18:17:13] + Attempting to send results [September 23 18:17:13 UTC]
[18:17:13] - Reading file work/wuresults_09.dat from core
[18:17:13] (Read 100185451 bytes from disk)
[18:17:13] Connecting to http://130.237.165.141:8080/
[18:17:14] - Couldn't send HTTP request to server
[18:17:14] + Could not connect to Work Server (results)
[18:17:14]    (130.237.165.141:8080)
[18:17:14] + Retrying using alternative port
[18:17:14] Connecting to http://130.237.165.141:80/
[18:17:14] - Couldn't send HTTP request to server
[18:17:14] + Could not connect to Work Server (results)
[18:17:14]    (130.237.165.141:80)
[18:17:14] Could not transmit unit 09 to Collection server; keeping in queue.
[18:17:14] + Sent 0 of 1 completed units to the server
[18:17:14] + Closed connections
[18:17:14]
[18:17:14] + Processing work unit
[18:17:14] Core required: FahCore_a5.exe
[18:17:14] Core found.
[18:17:14] Working on queue slot 00 [September 23 18:17:14 UTC]
[18:17:14] + Working ...
[18:17:14] - Calling '.\FahCore_a5.exe -dir work/ -nice 19 -suffix 00 -np 7 -checkpoint 5 -verbose -lifeline 3088 -version 634'

[18:17:14]
[18:17:14] *------------------------------*
[18:17:14] Folding@Home Gromacs SMP Core
[18:17:14] Version 2.27 (Mar 12, 2010)
[18:17:14]
[18:17:14] Preparing to commence simulation
[18:17:14] - Looking at optimizations...
[18:17:14] - Created dyn
[18:17:14] - Files status OK
[18:17:19] - Expanded 24865189 -> 30796292 (decompressed 123.8 percent)
[18:17:19] Called DecompressByteArray: compressed_data_size=24865189 data_size=30796292, decompressed_data_size=30796292 diff=0
[18:17:19] - Digital signature verified
[18:17:19]
[18:17:19] Project: 6900 (Run 34, Clone 16, Gen 12)
[18:17:19]
[18:17:19] Assembly optimizations on if available.
[18:17:19] Entering M.D.
[18:17:25] Mapping NT from 7 to 7
[18:17:28] Completed 0 out of 250000 steps  (0%)
[21:57:56] Completed 15000 out of 250000 steps  (6%)
[22:26:45] - Autosending finished units... [September 23 22:26:45 UTC]
[22:26:45] Trying to send all finished work units
[22:26:45] Project: 6900 (Run 54, Clone 17, Gen 4)

[22:26:45] + Attempting to send results [September 23 22:26:45 UTC]
[22:26:45] - Reading file work/wuresults_09.dat from core
[22:26:45] (Read 100185451 bytes from disk)
[22:26:45] Connecting to http://130.237.232.141:8080/
[22:34:39] Completed 17500 out of 250000 steps  (7%)
[22:44:25] - Couldn't send HTTP request to server
[22:44:25] + Could not connect to Work Server (results)
[22:44:25]    (130.237.232.141:8080)
[22:44:25] + Retrying using alternative port
[22:44:25] Connecting to http://130.237.232.141:80/
[22:44:25] - Couldn't send HTTP request to server
[22:44:25] + Could not connect to Work Server (results)
[22:44:25]    (130.237.232.141:80)
[22:44:25] - Error: Could not transmit unit 09 (completed September 23) to work server.
[22:44:25] - 4 failed uploads of this unit.

[22:44:25] + Attempting to send results [September 23 22:44:25 UTC]
[22:44:25] - Reading file work/wuresults_09.dat from core
[22:44:25] (Read 100185451 bytes from disk)
[22:44:25] Connecting to http://130.237.165.141:8080/
[22:44:26] - Couldn't send HTTP request to server
[22:44:26] + Could not connect to Work Server (results)
[22:44:26]    (130.237.165.141:8080)
[22:44:26] + Retrying using alternative port
[22:44:26] Connecting to http://130.237.165.141:80/
[22:44:27] - Couldn't send HTTP request to server
[22:44:27] + Could not connect to Work Server (results)
[22:44:27]    (130.237.165.141:80)
[22:44:27] Could not transmit unit 09 to Collection server; keeping in queue.
[22:44:27] + Sent 0 of 1 completed units to the server
[22:44:27] - Autosend completed
[23:11:20] Completed 20000 out of 250000 steps  (8%)
[04:05:00] Completed 40000 out of 250000 steps  (16%)

金鹏 · 发表于 2011-9-24 12:59:37

回复 39# shouldbe

这个RP还是网络。。。。。。。。

兄弟计算SMP2包能上传么？不行就跑SMP2把，

ONLY · 发表于 2011-9-24 14:49:07

SHOULDEBE兄弟如果木精力折腾，可以把平台发到偶这里，偶代为维护和跑分，分数是兄弟滴。

ONLY · 发表于 2011-9-24 22:02:58

本帖最后由 ONLY 于 2011-9-24 22:14 编辑

悲剧，算完了，但不能上传

[14:28:25] Completed 245000 out of 250000 steps (98%)
[15:04:19] Complete ...
shouldbe 发表于 2011-9-24 12:25

兄弟是否启用了Langouste？

若启用，请发个log文件看下～～～

（启用的话，需要重启电脑才会起作用）～～～

另外在日志中会有启用信息：

Wed Sep 21 05:17:55 2011 Langouste3 0.15.7 (compiled Sat Apr 30 13:54:54 MST 2011 by root@Build)
Wed Sep 21 05:17:55 2011 Langouste3 comes with ABSOLUTELY NO WARRANTY; for details
Wed Sep 21 05:17:55 2011 see `COPYING.txt' file located in source directory
Wed Sep 21 05:17:55 2011 Default Langouste helper temp directory: /tmp/langouste-fah/
Wed Sep 21 05:17:55 2011 Ratelimit: Output rate: 30720 bytes/s (30.00 kBps)
Wed Sep 21 05:17:55 2011 Listening on 127.0.0.1:8080
Wed Sep 21 05:17:55 2011 Going into backgound...

客户端启动的时候也会有相应的提示（注意端口号是否一致）～～～

--- Opening Log file [September 22 16:35:27 UTC]

# Linux SMP Console Edition ###################################################
###############################################################################

Folding@Home Client Version 6.34

http://folding.stanford.edu

###############################################################################
###############################################################################

Launch directory: /usr/local/fah
Executable: ./fah6
Arguments: -bigadv -verbosity 7 -smp 8

[16:35:27] - Ask before connecting: No
[16:35:27] - Proxy: localhost:8080
[16:35:27] - User name: ONLY (Team 3213)
[16:35:27] - User ID: 3D82DA6349EB63C2
[16:35:27] - Machine ID: 1
[16:35:27]
[16:35:28] Loaded queue successfully.

感觉兄弟是否误删了什么文件，造成Langouste工作不正常～～～

所以只下载，无法上传～～～

另外附上偶的log文件，貌似和兄弟的很相似：

[15:00:45] Completed 250000 out of 250000 steps (100%)
[15:00:50] DynamicWrapper: Finished Work Unit: sleep=10000
[15:01:00]
[15:01:00] Finished Work Unit:
[15:01:00] - Reading up to 52713120 from "work/wudata_02.trr": Read 52713120
[15:01:00] trr file hash check passed.
[15:01:00] - Reading up to 47067604 from "work/wudata_02.xtc": Read 47067604
[15:01:00] xtc file hash check passed.
[15:01:00] edr file hash check passed.
[15:01:00] logfile size: 198479
[15:01:00] Leaving Run
[15:01:01] - Writing 100149151 bytes of core data to disk...
[15:01:01] ... Done.
[15:01:14] - Shutting down core
[15:01:14]
[15:01:14] Folding@home Core Shutdown: FINISHED_UNIT
[15:01:15] CoreStatus = 64 (100)
[15:01:15] Unit 2 finished with 75 percent of time to deadline remaining.
[15:01:15] Updated performance fraction: 0.739751
[15:01:15] Sending work to server
[15:01:15] Project: 6900 (Run 20, Clone 23, Gen 55)

[15:01:15] + Attempting to send results [September 23 15:01:15 UTC]
[15:01:15] (Read 100149151 bytes from disk)
[15:01:15] Connecting to http://130.237.232.141:8080/
[15:01:15] - Couldn't send HTTP request to server
[15:01:15] + Could not connect to Work Server (results)
[15:01:15] (130.237.232.141:8080)
[15:01:15] + Retrying using alternative port
[15:01:15] Connecting to http://130.237.232.141:80/
[15:01:15] - Couldn't send HTTP request to server
[15:01:15] + Could not connect to Work Server (results)
[15:01:15] (130.237.232.141:80)
[15:01:15] - Error: Could not transmit unit 02 (completed September 23) to work server.
[15:01:15] Keeping unit 02 in queue.
[15:01:15] Trying to send all finished work units
[15:01:15] Project: 6900 (Run 20, Clone 23, Gen 55)

[15:01:15] + Attempting to send results [September 23 15:01:15 UTC]
[15:01:15] (Read 100149151 bytes from disk)
[15:01:15] Connecting to http://130.237.232.141:8080/
[15:01:15] - Couldn't send HTTP request to server
[15:01:15] + Could not connect to Work Server (results)
[15:01:15] (130.237.232.141:8080)
[15:01:15] + Retrying using alternative port
[15:01:15] Connecting to http://130.237.232.141:80/
[15:01:15] - Couldn't send HTTP request to server
[15:01:15] + Could not connect to Work Server (results)
[15:01:15] (130.237.232.141:80)
[15:01:15] - Error: Could not transmit unit 02 (completed September 23) to work server.

[15:01:15] + Attempting to send results [September 23 15:01:15 UTC]
[15:01:15] (Read 100149151 bytes from disk)
[15:01:15] Connecting to http://130.237.165.141:8080/
[15:01:15] - Couldn't send HTTP request to server
[15:01:15] + Could not connect to Work Server (results)
[15:01:15] (130.237.165.141:8080)
[15:01:15] + Retrying using alternative port
[15:01:15] Connecting to http://130.237.165.141:80/
[15:01:15] - Couldn't send HTTP request to server
[15:01:15] + Could not connect to Work Server (results)
[15:01:15] (130.237.165.141:80)
[15:01:15] Could not transmit unit 02 to Collection server; keeping in queue.
[15:01:15] + Sent 0 of 1 completed units to the server
[15:01:15] - Preparing to get new work unit...
[15:01:15] Cleaning up work directory
[15:01:15] + Attempting to get work packet
[15:01:15] Passkey found
[15:01:15] - Will indicate memory of 3911 MB
[15:01:15] - Connecting to assignment server
[15:01:15] Connecting to http://assign.stanford.edu:8080/
[15:01:16] - Successful: assigned to (130.237.232.141).
[15:01:16] + News From Folding@Home: Welcome to Folding@Home
[15:01:16] Loaded queue successfully.
[15:01:16] Sent data
[15:01:16] Connecting to http://130.237.232.141:8080/
[15:08:46] - Downloaded at ~54 kB/s
[15:08:46] - Averaged speed for that direction ~90 kB/s
[15:08:46] + Received work.
[15:08:46] Trying to send all finished work units
[15:08:46] Project: 6900 (Run 20, Clone 23, Gen 55)

[15:08:46] + Attempting to send results [September 23 15:08:46 UTC]
[15:08:46] (Read 100149151 bytes from disk)
[15:08:46] Connecting to http://130.237.232.141:8080/
[15:08:46] - Couldn't send HTTP request to server
[15:08:46] + Could not connect to Work Server (results)
[15:08:46] (130.237.232.141:8080)
[15:08:46] + Retrying using alternative port
[15:08:46] Connecting to http://130.237.232.141:80/
[15:08:46] - Couldn't send HTTP request to server
[15:08:46] + Could not connect to Work Server (results)
[15:08:46] (130.237.232.141:80)
[15:08:46] - Error: Could not transmit unit 02 (completed September 23) to work server.

[15:08:46] + Attempting to send results [September 23 15:08:46 UTC]
[15:08:46] (Read 100149151 bytes from disk)
[15:08:46] Connecting to http://130.237.165.141:8080/
[15:08:46] - Couldn't send HTTP request to server
[15:08:46] + Could not connect to Work Server (results)
[15:08:46] (130.237.165.141:8080)
[15:08:46] + Retrying using alternative port
[15:08:46] Connecting to http://130.237.165.141:80/
[15:08:46] - Couldn't send HTTP request to server
[15:08:46] + Could not connect to Work Server (results)
[15:08:46] (130.237.165.141:80)
[15:08:46] Could not transmit unit 02 to Collection server; keeping in queue.
[15:08:46] + Sent 0 of 1 completed units to the server
[15:08:46] + Closed connections
[15:08:46]
[15:08:46] + Processing work unit
[15:08:46] Core required: FahCore_a5.exe
[15:08:46] Core found.
[15:08:46] Working on queue slot 03 [September 23 15:08:46 UTC]
[15:08:46] + Working ...
[15:08:46]
[15:08:46] *------------------------------*
[15:08:46] Folding@Home Gromacs SMP Core
[15:08:46] Version 2.27 (Thu Feb 10 09:46:40 PST 2011)
[15:08:46]
[15:08:46] Preparing to commence simulation
[15:08:46] - Looking at optimizations...
[15:08:46] - Created dyn
[15:08:46] - Files status OK
[15:08:47] - Expanded 24870214 -> 30796292 (decompressed 123.8 percent)
[15:08:47] Called DecompressByteArray: compressed_data_size=24870214 data_size=30796292, decompressed_data_size=30796292 diff=0
[15:08:47] - Digital signature verified
[15:08:47]
[15:08:47] Project: 6900 (Run 52, Clone 13, Gen 38)
[15:08:47]
[15:08:47] Assembly optimizations on if available.
[15:08:47] Entering M.D.
[15:08:54] Mapping NT from 8 to 8
[15:08:55] Completed 0 out of 250000 steps (0%)

下面则是Langoust.log文件，可以看到客户端多次的尝试上传，然后Langouste实际接管上传工作：

Fri Sep 23 15:01:15 2011 Accepted connection from: 127.0.0.1:46990
Fri Sep 23 15:01:15 2011 PID for socket: 1104
Fri Sep 23 15:01:15 2011 PID 1104: issending: 0
Fri Sep 23 15:01:15 2011 ===> PID 1104 is (most likely) contacting WU server, content length: 100149663
Fri Sep 23 15:01:15 2011 ===> Helper pid: -1
Fri Sep 23 15:01:15 2011 ===> PID 1104: numcores: 0
Fri Sep 23 15:01:15 2011 ===> now: 1316790075, last helper launched at: 0
Fri Sep 23 15:01:15 2011 ===> Launching helper: '/proc/1104/cwd/langouste-helper.sh' (exe name: '/usr/local/fah/fah6')...
Fri Sep 23 15:01:15 2011 ===> Forked 3774
Fri Sep 23 15:01:15 2011 (0) Local: received 16384 bytes, sent 0 bytes
Fri Sep 23 15:01:15 2011 Accepted connection from: 127.0.0.1:46991
Fri Sep 23 15:01:15 2011 PID for socket: 1104
Fri Sep 23 15:01:15 2011 PID 1104: issending: 0
Fri Sep 23 15:01:15 2011 ===> PID 1104 is (most likely) contacting WU server, content length: 100149663
Fri Sep 23 15:01:15 2011 ===> Helper pid: -1
Fri Sep 23 15:01:15 2011 ===> PID 1104: numcores: 0
Fri Sep 23 15:01:15 2011 ===> now: 1316790075, last helper launched at: 1316790075
Fri Sep 23 15:01:15 2011 ===> WARNING: can only launch one helper in 2 minutes (per client)
Fri Sep 23 15:01:15 2011 (0) Local: received 16384 bytes, sent 0 bytes
Fri Sep 23 15:01:15 2011 Accepted connection from: 127.0.0.1:46992
Fri Sep 23 15:01:15 2011 PID for socket: 1104
Fri Sep 23 15:01:15 2011 PID 1104: issending: 0
Fri Sep 23 15:01:15 2011 ===> PID 1104 is (most likely) contacting WU server, content length: 100149663
Fri Sep 23 15:01:15 2011 ===> Helper pid: -1
Fri Sep 23 15:01:15 2011 ===> PID 1104: numcores: 0
Fri Sep 23 15:01:15 2011 ===> now: 1316790075, last helper launched at: 1316790075
Fri Sep 23 15:01:15 2011 ===> WARNING: can only launch one helper in 2 minutes (per client)
Fri Sep 23 15:01:15 2011 (0) Local: received 16384 bytes, sent 0 bytes
Fri Sep 23 15:01:15 2011 Accepted connection from: 127.0.0.1:46993
Fri Sep 23 15:01:15 2011 PID for socket: 1104
Fri Sep 23 15:01:15 2011 PID 1104: issending: 0
Fri Sep 23 15:01:15 2011 ===> PID 1104 is (most likely) contacting WU server, content length: 100149663
Fri Sep 23 15:01:15 2011 ===> Helper pid: -1
Fri Sep 23 15:01:15 2011 ===> PID 1104: numcores: 0
Fri Sep 23 15:01:15 2011 ===> now: 1316790075, last helper launched at: 1316790075
Fri Sep 23 15:01:15 2011 ===> WARNING: can only launch one helper in 2 minutes (per client)
Fri Sep 23 15:01:15 2011 (0) Local: received 16384 bytes, sent 0 bytes
Fri Sep 23 15:01:15 2011 Accepted connection from: 127.0.0.1:46994
Fri Sep 23 15:01:15 2011 PID for socket: 1104
Fri Sep 23 15:01:15 2011 PID 1104: issending: 0
Fri Sep 23 15:01:15 2011 ===> PID 1104 is (most likely) contacting WU server, content length: 100149663
Fri Sep 23 15:01:15 2011 ===> Helper pid: -1
Fri Sep 23 15:01:15 2011 ===> PID 1104: numcores: 0
Fri Sep 23 15:01:15 2011 ===> now: 1316790075, last helper launched at: 1316790075
Fri Sep 23 15:01:15 2011 ===> WARNING: can only launch one helper in 2 minutes (per client)
Fri Sep 23 15:01:15 2011 (0) Local: received 16384 bytes, sent 0 bytes
Fri Sep 23 15:01:15 2011 Accepted connection from: 127.0.0.1:46995
Fri Sep 23 15:01:15 2011 PID for socket: 1104
Fri Sep 23 15:01:15 2011 PID 1104: issending: 0
Fri Sep 23 15:01:15 2011 ===> PID 1104 is (most likely) contacting WU server, content length: 100149663
Fri Sep 23 15:01:15 2011 ===> Helper pid: -1
Fri Sep 23 15:01:15 2011 ===> PID 1104: numcores: 0
Fri Sep 23 15:01:15 2011 ===> now: 1316790075, last helper launched at: 1316790075
Fri Sep 23 15:01:15 2011 ===> WARNING: can only launch one helper in 2 minutes (per client)
Fri Sep 23 15:01:15 2011 (0) Local: received 16384 bytes, sent 0 bytes
Fri Sep 23 15:01:15 2011 Accepted connection from: 127.0.0.1:46996
Fri Sep 23 15:01:15 2011 PID for socket: 1104
Fri Sep 23 15:01:15 2011 PID 1104: issending: 0
Fri Sep 23 15:01:15 2011 ===> PID 1104 is contacting main assignment server
Fri Sep 23 15:01:15 2011 (0) resolving 'assign.stanford.edu:8080'
Fri Sep 23 15:01:16 2011 (0) Connecting to: 171.67.108.200:8080
Fri Sep 23 15:01:16 2011 (0) Connected.
Fri Sep 23 15:01:16 2011 (0) Local connection closed (bsize: 0).
Fri Sep 23 15:01:16 2011 (0) Local: received 559 bytes, sent 396 bytes
Fri Sep 23 15:01:16 2011 (0) Remote: received 396 bytes, sent 559 bytes
Fri Sep 23 15:01:16 2011 Accepted connection from: 127.0.0.1:46998
Fri Sep 23 15:01:16 2011 PID for socket: 1104
Fri Sep 23 15:01:16 2011 PID 1104: issending: 0
Fri Sep 23 15:01:16 2011 ===> PID 1104 is (most likely) contacting WU server, content length: 512
Fri Sep 23 15:01:16 2011 (0) resolving '130.237.232.141:8080'
Fri Sep 23 15:01:16 2011 (0) Connecting to: 130.237.232.141:8080
Fri Sep 23 15:01:17 2011 (0) Connected.
Fri Sep 23 15:02:16 2011 Accepted connection from: 127.0.0.1:47000
Fri Sep 23 15:02:16 2011 PID for socket: 3789
Fri Sep 23 15:02:16 2011 PID 3789: issending: 1
Fri Sep 23 15:02:16 2011 (1) resolving '130.237.232.141:8080'
Fri Sep 23 15:02:16 2011 (1) Connecting to: 130.237.232.141:8080
Fri Sep 23 15:02:16 2011 (1) Connected.
Fri Sep 23 15:08:46 2011 (0) Remote connection closed (rbsize: 0).
Fri Sep 23 15:08:46 2011 (0) Local: received 631 bytes, sent 24871346 bytes
Fri Sep 23 15:08:46 2011 (0) Remote: received 24871346 bytes, sent 631 bytes
Fri Sep 23 15:08:46 2011 Accepted connection from: 127.0.0.1:49133
Fri Sep 23 15:08:46 2011 PID for socket: 1104
Fri Sep 23 15:08:46 2011 PID 1104: issending: 0
Fri Sep 23 15:08:46 2011 ===> PID 1104 is (most likely) contacting WU server, content length: 100149663
Fri Sep 23 15:08:46 2011 ===> Helper pid: 3789
Fri Sep 23 15:08:46 2011 ===> PID 1104: numcores: 0
Fri Sep 23 15:08:46 2011 ===> Helper (pid 3789) already running
Fri Sep 23 15:08:46 2011 ===> If you're sure that's not the case, please remove /tmp/fah/f1
Fri Sep 23 15:08:46 2011 (0) Local: received 16384 bytes, sent 0 bytes
Fri Sep 23 15:08:46 2011 Accepted connection from: 127.0.0.1:49134
Fri Sep 23 15:08:46 2011 PID for socket: 1104
Fri Sep 23 15:08:46 2011 PID 1104: issending: 0
Fri Sep 23 15:08:46 2011 ===> PID 1104 is (most likely) contacting WU server, content length: 100149663
Fri Sep 23 15:08:46 2011 ===> Helper pid: 3789
Fri Sep 23 15:08:46 2011 ===> PID 1104: numcores: 0
Fri Sep 23 15:08:46 2011 ===> Helper (pid 3789) already running
Fri Sep 23 15:08:46 2011 ===> If you're sure that's not the case, please remove /tmp/fah/f1
Fri Sep 23 15:08:46 2011 (0) Local: received 16384 bytes, sent 0 bytes
Fri Sep 23 15:08:46 2011 Accepted connection from: 127.0.0.1:49135
Fri Sep 23 15:08:46 2011 PID for socket: 1104
Fri Sep 23 15:08:46 2011 PID 1104: issending: 0
Fri Sep 23 15:08:46 2011 ===> PID 1104 is (most likely) contacting WU server, content length: 100149663
Fri Sep 23 15:08:46 2011 ===> Helper pid: 3789
Fri Sep 23 15:08:46 2011 ===> PID 1104: numcores: 0
Fri Sep 23 15:08:46 2011 ===> Helper (pid 3789) already running
Fri Sep 23 15:08:46 2011 ===> If you're sure that's not the case, please remove /tmp/fah/f1
Fri Sep 23 15:08:46 2011 (0) Local: received 16384 bytes, sent 0 bytes
Fri Sep 23 15:08:46 2011 Accepted connection from: 127.0.0.1:49136
Fri Sep 23 15:08:46 2011 PID for socket: 1104
Fri Sep 23 15:08:46 2011 PID 1104: issending: 0
Fri Sep 23 15:08:46 2011 ===> PID 1104 is (most likely) contacting WU server, content length: 100149663
Fri Sep 23 15:08:46 2011 ===> Helper pid: 3789
Fri Sep 23 15:08:46 2011 ===> PID 1104: numcores: 0
Fri Sep 23 15:08:46 2011 ===> Helper (pid 3789) already running
Fri Sep 23 15:08:46 2011 ===> If you're sure that's not the case, please remove /tmp/fah/f1
Fri Sep 23 15:08:46 2011 (0) Local: received 16384 bytes, sent 0 bytes
Fri Sep 23 16:15:57 2011 (1) Remote connection closed (rbsize: 0).
Fri Sep 23 16:15:57 2011 (1) Local: received 100149788 bytes, sent 615 bytes
Fri Sep 23 16:15:57 2011 (1) Remote: received 615 bytes, sent 100149788 bytes
Fri Sep 23 16:15:57 2011 (1) Ratelimit: sent 100149788 byte(s) in 4420.639 seconds, 22655 Bps (22.12 kBps)

shouldbe · 发表于 2011-9-24 23:27:20

Langoust是linux的。winxp客户端下没有这个东东。

白天改算SMP。已经成功上传一个：

[10:15:40] + Attempting to send results [September 24 10:15:40 UTC]
[10:15:40] - Reading file work/wuresults_04.dat from core
[10:15:40] (Read 3791811 bytes from disk)
[10:15:40] Connecting to http://171.64.65.54:8080/
[10:28:05] - Autosending finished units... [September 24 10:28:05 UTC]
[10:28:05] Trying to send all finished work units
[10:28:05] - Already sending work
[10:28:05] + Sent 0 of 1 completed units to the server
[10:28:05] - Autosend completed
[10:29:57] Posted data.
[10:29:57] Initial: 0000; - Uploaded at ~4 kB/s
[10:29:58] - Averaged speed for that direction ~4 kB/s
[10:29:58] + Results successfully sent
[10:29:58] Thank you for your contribution to Folding@Home.
[10:29:58] + Number of Units Completed: 726

shouldbe · 发表于 2011-9-24 23:27:40

bigadv还是无法上传。晕菜。

ONLY · 发表于 2011-9-24 23:34:05

上传速度实在是让人无语啊，才4K~~~

		自动登录	找回密码
密码			新注册用户

[求助] 内牛……bigadv算到一半……重启之后从0开始了……